m menu image  m home m cart

SER-DMX

$359.96

Quantity:     
Package Contents:
1 - SER-DMX
1 - Gilder CD w/Software & Manuals
Suggested Accessories

DMX-512 & ServoMotor Output miniBrick

The SER-DMX is used for controlling remote control-style ServoMotors from its micro Sd card, or from any Gilderfluke Animation Control System or other DMX-512 source. ServoMotors are an inexpensive way to add analog movements to animated figures.

A Digital device is either on or off, like a light switch. An Analog device is on, off, or at any point between. A common example of an analog device is a lamp dimmer. In animation, analog movements give the fluid, lifelike movements that are needed to bring an animated figure to life. Analog movements can be moved as quickly or slowly as you desire, and stopped at any point within their range of movement.

Features of the SER-DMX include:
  • The SER-DMX controls up to sixteen remote control-style ServoMotors. These use a Pulse Code Modulated (PCM) command signal with pulses that typically vary between 1.0 and 2.0 milliseconds to give you a 90° ServoMotor shaft rotation. Each ServoMotor output can be adjusted anywhere between .5 and 2.5 milliseconds, or even reversed. Depending on your ServoMotor, this can give you up to 180 degrees of movement. The ServoMotor endpoints do not interact during adjustment.
  • Accepts eight or twelve bit resolution commands from your Pc•MACs Animation Programming System.
  • Built-in Ease-In when shows or DMX-512 starts or stops. These keep the ServoMotors from jumping.
  • SER-DMX diagram
  • Networkable! The SER-DMX can act as a ‘master’, sending up to 512 channels of DMX-512 data to other GilderGear and DMX-512-compatible equipment that act as a ‘slaves’, or the SER-DMX can receive DMX-512 from an external source, and itself be a ‘slave’. Error checking prevents any updates from bad DMX-512 data. As a ‘Master’, the SER-DMX has the DMX-512 output capacity to run most shows.
  • Micro Sd Flash card for a virtually unlimited show capacity. Up to 255 shows can be loaded onto a SER-DMX at one time. In many installations, the SER-DMX can take the place of a lighting board.
  • Indicator LEDs for heartbeat, trigger inputs, ServoMotor outputs, and DMX-512 status.
  • Two optoisolated inputs or the RS-232 serial port can be used to start, stop, or access shows.
  • The SER-DMX cards can be mounted in ‘inaccessible’ locations, since they are Controlled and Configured through the RS-232 serial port.
  • The SER-DMX runs on 7 to 24 vdc. ServoMotors typically use 4 to 6 volts. Some ServoMotors use up to 12 or 24 vdc. If using ServoMotors that need more than seven volts, you can run the SER-DMX from the same supply as the ServoMotors.
  • Identical in size and shape to a Br-miniBrick8. Can be mounted on Snap-Track, DIN rail (using the optional DinAdapt clips), or just screw or velcro it to the backside of whatever it is controlling.
SER-DMX Suggested Accessories:
Input Devices
DMX-512
Output Devices
PWM Servo
DMX-512 I/O Devices
MACS-USB
TOG-02
MACs-CON
MACs-EncCon
Micro-CON2
Mp3-50-8
Mp3-50/8c
Mp3-50/40
Mp3-50/40c
Serial I/O Devices
Mounting Options
Screw Down
Cables
 
Misc.
N/A



Back




Copyright © 2017 Gilderfluke & Co.. Design by Duckweb Studio